高烈度地震区隧道软硬围岩交接段刚柔并济抗减震技术研究*

为提高高烈度地震区隧道抗震性能，以某铁路隧道为研究背景，分析3种抗减震措施下隧道不同监测点隧道拱顶沉降、边墙收敛、衬砌结构PGA及最小安全系数，通过对比分析得到最优抗减震措施。结果表明:相比于工况1，工况2隧道拱顶沉降减小10.54%~81.10%，边墙收敛减小13.92%~78.77%，衬砌结构PGA减小31.42%~72.02%，最小安全系数增加18.04%~66.13%；相比于工况1，工况3结构拱顶沉降减小3.04%~18.02%，边墙收敛减小4.70%~32.00%，PGA增加13.95%~27.48%，最小安全系数增加7.49%~30.99%；工况4即“减震层+SFRC衬砌”刚柔并济法，相比于工况1，隧道拱顶沉降减小18.46%~83.98%，结构边墙收敛减小17.54%~85.47%，PGA减小30.00%~69.98%，最小安全系数增加47.95%~83.56%；4种工况抗减震性能由高到低依次为:工况4＞工况2＞工况3＞工况1。研究结果可为隧道软硬围岩交接段抗震设防提供理论参考。     

Are older drivers’ driving patterns during an on-road driving task representative of their real-world driving patterns?

Abstract

Objective: The current study investigated whether older drivers’ driving patterns during a customized on-road driving task were representative of their real-world driving patterns.

Methods: Two hundred and eight participants (male: 68.80%; mean age?=?81.52 years, SD?=?3.37 years, range?=?76.00–96.00 years) completed a customized on-road driving task that commenced from their home and was conducted in their own vehicle. Participants’ real-world driving patterns for the preceding 4-month period were also collected via an in-car recording device (ICRD) that was installed in each participant’s vehicle.

Results: During the 4-month period prior to completing the on-road driving task, participants’ median real-world driving trip distance was 2.66?km (interquartile range [IQR]?=?1.14–5.79?km) and their median on-road driving task trip distance was 4.41?km (IQR?=?2.83–6.35?km). Most participants’ on-road driving task trip distances were classified as representative of their real-world driving trip distances (95.2%, n?=?198).

Conclusions: These findings suggest that most older drivers were able to devise a driving route that was representative of their real-world driving trip distance. Future research will examine whether additional aspects of the on-road driving task (e.g., average speed, proportion of trips in different speed zones) are representative of participants’ real-world driving patterns.     

高含盐废水脱盐处理技术研究进展

综述了几种常见的高含盐废水脱盐处理技术的发展历程、工艺原理、优缺点及目前的研究进展，分析了热分离、膜分离、电渗析、离子交换、电吸附、微生物脱盐等方法的优缺点，展望了未来废水脱盐工艺的发展方向。指出：脱盐方法将根据各类水体的水质特点更加精细化；多种脱盐技术联合应用也是今后废水脱盐的发展方向。     

SMBBR-AF-SMBBR组合工艺处理高氨氮农药废水

采用特异性移动床生物膜反应器(SMBBR)和厌氧生物滤池(AF)组合工艺处理高氨氮农药废水。考察了HRT、pH和DO等工艺条件对SMBBR-AF-SMBBR组合工艺运行稳定期COD和氨氮去除率的影响。试验结果表明,在进水COD为2 408~7 440 mg/L、ρ(NH_4~+-N)为160.21~433.84 mg/L、TN为208.27~537.65 mg/L、HRT为8d、pH为8.0、DO为4 mg/L的条件下,处理后出水平均COD为342 mg/L,COD去除率达92.3%;ρ(NH_4~+-N)小于4.0mg/L,氨氮平均去除率为89.2%;TN小于50 mg/L,平均TN去除达83.0%。出水各指标均优于原A2O工艺出水。     

活性炭吸附和两级Fenton氧化组合工艺处理高盐对氨基苯酚生产废水

采用活性炭吸附和两级Fenton氧化组合工艺对高盐度对氨基苯酚生产废水进行了处理实验研究。结果表明,p H值对活性炭去除有机物的影响较小。当活性炭投加量为4 g/L时,TOC去除率61%。分级加药可以有效提高Fenton氧化对有机物的去除效率。在温度为25℃、p H为3、30%H2O2投加量为3%(V/V)、Fe2+/H2O2摩尔比为0.05时,两级Fenton氧化处理后,出水TOC降至150 mg/L以下。此外,Fenton氧化后形成氢氧化铁污泥颗粒粒径为4.5μm,经过聚丙烯酰胺(PAM)絮凝之后,污泥的粒径明显增加,过滤特性改善。PAM絮凝效果依赖于溶液的p H值,当p H超过10后会失去作用,故在使用过程中需要严格控制溶液的p H值。     

高效液相色谱-二极管阵列检测器测定邻苯二甲酸酯色谱条件优化

采用高效液相色谱-二极管阵列检测器对6种PAEs类物质进行测定,并对梯度洗脱条件、流速、检测波长等影响化合物色谱响应的关键参数进行优化。综合考虑样品测试效率、分析精度、实际样品中存在杂质干扰等因素,确定以乙腈-水为流动相进行梯度洗脱,洗脱0~11 min流动相乙腈-水梯度比例为50∶50,11 min后流动相调整为100%乙腈,各化合物均能完全分离;色谱分析流速为0.8 m L/min;PAEs的最佳吸收波长为225 nm。在优化的色谱条件下,6种PAEs的线性良好,相关系数均大于0.999 8,仪器检出限为0.08~0.12 mg/L,保留时间、峰面积的相对标准偏差分别为0.02%~0.60%、0.13%~0.86%。方法灵敏度较高,适合土壤等邻苯二甲酸酯含量较高基质样品的快速分析。     

基于SOF-FTIR方法走航观测南京市重点区域特征挥发性有机物

介绍了污染源挥发性有机物(VOCs)排放的常用监测方法,以及基于红外掩日通量-傅里叶变换红外光谱(SOF-FTIR)的走航观测系统结构与测试原理。以2014年南京青奥会期间对一些重点区域VOCs的走航观测为例,提出了借鉴前期现状调查结果,结合手工采样分析,确定特征目标组分的监测方案。观测结果表明,该方法在柱浓度监测和排放总量核算方面具有一定优势,不足之处在于受日照条件、走航速度和路况、地面风速限制,测量时需避开不利因素影响。     

高温高压下煤孔隙结构的变化对瓦斯吸附特性的影响

为了研究高温高压条件下煤孔隙结构变化对瓦斯吸附特性的影响，选取九里山矿无烟煤，在压力为7 MPa、温度为40～130℃的条件下进行等温吸附实验和压汞实验。研究结果表明:煤样对甲烷的等温吸附曲线在该压力、温度条件下符合Ⅰ型吸附曲线特性，吸附规律符合Langmuir吸附模型；在压力7 MPa和温度130℃条件下，煤样的孔隙结构发生一定的变化，煤的比表面积增大、累计孔体积降低，可见孔及裂隙的数量比例增高，加强了煤样孔隙之间的连通度，导致原本吸附在煤样表面的甲烷分子大量解吸；在压力不变的情况下，随着温度的不断增高，煤的极限吸附量逐渐减小，其主要原因是样品孔隙结构的破坏和分子间作用力的变化。     

高瓦斯工作面隅角柔性气囊安全封堵研究

为解决高瓦斯工作面隅角封堵工人劳动强度大、效率低,封堵效果不佳易造成隅角瓦斯浓度超限等安全问题,研发设计了矿用阻燃内外胆组合结构的轻型柔性隅角封堵气囊,并相应提出了单体液压支柱配合轻型柔性气囊的隅角封堵新方法。通过实验室测试实验和现场工业性试验表明:选用PVC材料和双抗涂覆布材料的气囊质量小、轻便实用,大幅降低了工人的劳动强度,提高了工作效率,减小了传统封堵方式编织袋装碎煤造成的遗煤浪费;该气囊可适应大变形(变形率可达42.5%)、耐冲击(2×104J的冲击能量不破坏),抗撕扯能力强,且具有阻燃特性,重复使用率高,大大节约了隅角封堵的成本;使用气囊封堵后,采空区内瓦斯浓度显著增大,说明气囊封堵的密闭性增加,安全封堵效果十分明显。     

Development and evaluation of RAMP I – a practitioner’s tool for screening of musculoskeletal disorder risk factors in manual handling

RAMP I is a screening tool developed to support practitioners in screening for work-related musculoskeletal disorder risk factors related to manual handling. RAMP I, which is part of the RAMP tool, is based on research-based studies combined with expert group judgments. More than 80 practitioners participated in the development of RAMP I. The tool consists of dichotomous assessment items grouped into seven categories. Acceptable reliability was found for a majority of the assessment items for 15 practitioners who were given 1?h of training. The usability evaluation points to RAMP I being usable for screening for musculoskeletal disorder risk factors, i.e., usable for assessing risks, being usable as a decision base, having clear results and that the time needed for an assessment is acceptable. It is concluded that RAMP I is a usable tool for practitioners.